1、#ifdef CONFIG_MEMORY_UPPER_CODE /* by scsuh */
ulong gd_base;
gd_base = CFG_UBOOT_BASE + CFG_UBOOT_SIZE - CFG_MALLOC_LEN - CFG_STACK_SIZE - sizeof(gd_t);
#ifdef CONFIG_USE_IRQ
gd_base -= (CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ);
#endif
gd = (gd_t*)gd_base;
#else
gd = (gd_t*)(_armboot_start - CFG_MALLOC_LEN - sizeof(gd_t));
#endif
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
memset ((void*)gd,sizeof (gd_t));
gd->bd = (bd_t*)((char*)gd - sizeof(bd_t));
memset (gd->bd,sizeof (bd_t));
为gd_t和bd_t结构体分配内存并初始化
2、调用通用初始化函数?
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {?
? ? ? ? ? ?if ((*init_fnc_ptr)() != 0) {?
? ? ? ? ? ? ? ? hang ();?
? ? ? ? ? ?}?
? ? ? }?
init_sequence[]是init_fnc_t 函数指针数组,这个数组包含了众多初始化函数,比如cpu_init,?
board_init 等。?
? ? ? ? ? ? ? ? ? //init_fnc_t *init_sequence[] = {?
? ? ? ? ? ? ? ? ? ? ? // ? cpu_init,? ? ? ?/* basic cpu dependent setup */?
? ? ? ? ? ? ? ? ? ? ? // ? board_init,? ? ? ? /* basic board dependent setup */?
? ? ? ? ? ? ? ? ? ? ?// ? ?interrupt_init,? ? ? ?/* set up exceptions */?
? ? ? ? ? ? ? ? ? ? ?// ? ?env_init,? ? ? ?/* initialize environment */?
? ? ? ? ? ? ? ? ? ? ? // ? init_baudrate,? ? ? ? /* initialze baudrate settings */?
? ? ? ? ? ? ? ? ? ? // ? ? serial_init,? ? ? /* serial communications setup */?
? ? ? ? ? ? ? ? ? ? // ? ? display_banner,?
? ? ? ? ? ? ? ? ? ? // ? ? dram_init,? ? ? ? /* configure available RAM banks */?
? ? ? ? ? ? ? ? ? ? // ? ? display_dram_config,?
? ? ? ? ? ? ? ? ? ? // ? ? NULL,?
? ? ? ? ? ? ? ? ? ? // ? ? };?
3、具体设备初始化
#ifndef CFG_NO_FLASH
/* configure available FLASH banks */
size = flash_init ();
display_flash_config (size);
#endif /* CFG_NO_FLASH */
#ifdef CONFIG_VFD
# ifndef PAGE_SIZE
# ?define PAGE_SIZE 4096
# endif
/*
* reserve memory for VFD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
size = vfd_setmem (addr);
gd->fb_base = addr;
#endif /* CONFIG_VFD */
#ifdef CONFIG_LCD
# ifndef PAGE_SIZE
# ?define PAGE_SIZE 4096
# endif
/*
* reserve memory for LCD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
size = lcd_setmem (addr);
gd->fb_base = addr;
#endif /* CONFIG_LCD */
/* armboot_start is defined in the board-specific linker script */
#ifdef CONFIG_MEMORY_UPPER_CODE /* by scsuh */
mem_malloc_init (CFG_UBOOT_BASE + CFG_UBOOT_SIZE - CFG_MALLOC_LEN - CFG_STACK_SIZE);
#else
mem_malloc_init (_armboot_start - CFG_MALLOC_LEN);
#endif
#if defined(CONFIG_SMDK6400) || defined(CONFIG_SMDK6410) || defined(CONFIG_SMDK6430) || defined(CONFIG_SMDK2450) || defined(CONFIG_SMDK2416)
? ?#if defined(CONFIG_NAND)
? ? puts ("NAND: ? ?");
? ? nand_init(); /* go init the NAND */
? ?#endif
? ??
? ? #if defined(CONFIG_ONENAND)
? ? puts ("OneNAND: ");
? ? onenand_init(); /* go init the One-NAND */
? ? #endif
? ??
? ? #if defined(CONFIG_BOOT_MOVINAND)
? ? puts ("SD/MMC: ?");
? ??
? ? if ((0x24564236 == magic[0]) && (0x20764316 == magic[1])) {
? ? printf("Boot up for burningn");
? ? } else {
? ? movi_set_capacity();
? ? movi_set_ofs(MOVI_TOTAL_BLKCNT);
? ? movi_init();
? ? }
? ? #endif
#else
? #if (CONFIG_COMMANDS & CFG_CMD_NAND)
? puts ("NAND: ? ?");
? nand_init(); /* go init the NAND */
? #endif
#endif
4、环境变量初始化
环境变量在通用初始化函数里面,已经初始化一次(env_init ),这里调用env_relocate 对环?
境变量进行重新定位。
/* initialize environment */
env_relocate ();
5、进入主循环
/* main_loop() can return to retry autoboot,if so just run it again. */ for (;;) { main_loop (); }