|
《LINUX入门：CentOS6 虚拟机迁移后网卡名更改问题解决》要点：
本文介绍了LINUX入门：CentOS6 虚拟机迁移后网卡名更改问题解决，希望对您有用。如果有疑问，可以联系我们。
实验过程中,我们经常必要复制虚拟机,以模仿生产过程中同等配置的条件.
但无论是初次打开,选择"我已复制该虚拟机“也好,还是在虚拟机设置>网络适配器>高级中重新生成Mac地址,开机后选择”我已移动该虚拟机“也罢.开机后查询IP时,我们都会很遗憾的发现,网卡的名字,纷歧样了.
这是因为原Mac地址占用旧网卡,新Mac地址只能使用新的网卡名称.复制虚拟机为了不与原虚拟机冲突,也是天生了新的Mac地址.
[root@CentOS6 ~]# ifconfig
eth2? ? ? Link encap:Ethernet? HWaddr 00:50:56:22:C9:22?
? ? ? ? ? inet addr:192.168.234.187? Bcast:192.168.234.255? Mask:255.255.255.0
? ? ? ? ? inet6 addr: fe80::250:56ff:fe22:c922/64 Scope:Link
? ? ? ? ? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1?
? ? ? ? ? RX packets:4 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:1000?
? ? ? ? ? RX bytes:806 (806.0 b)? TX bytes:1152 (1.1 KiB)
eth3? ? ? Link encap:Ethernet? HWaddr 00:50:56:3A:FD:74?
? ? ? ? ? inet addr:172.17.251.174? Bcast:172.17.255.255? Mask:255.255.0.0
? ? ? ? ? inet6 addr: fe80::250:56ff:fe3a:fd74/64 Scope:Link
? ? ? ? ? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1
? ? ? ? ? RX packets:2565 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:61 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:1000?
? ? ? ? ? RX bytes:243027 (237.3 KiB)? TX bytes:9974 (9.7 KiB)
lo? ? ? ? Link encap:Local Loopback?
? ? ? ? ? inet addr:127.0.0.1? Mask:255.0.0.0
? ? ? ? ? inet6 addr: ::1/128 Scope:Host
? ? ? ? ? UP LOOPBACK RUNNING? MTU:65536? Metric:1
? ? ? ? ? RX packets:4 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:0?
? ? ? ? ? RX bytes:240 (240.0 b)? TX bytes:240 (240.0 b)
虽然不影响使用,但怎么看都不舒服啊.而且有些实验中网卡名不统一也只有麻烦.正所谓没有标准化就很难进行自动化管理.
那么,如何变动迁移后的虚拟机的网卡名呢?
(1).改动配置文件/etc/udev/rules.d/70-persistent-net.rules
[root@centos6 ~]# vim /etc/udev/rules.d/70-persistent-net.rules?
# This file was automatically generated by the /lib/udev/write_net_rules
# program,run by the persistent-net-generator.rules rules file.
#
# You can modify it,as long as you keep each rule on a single
# line,and change only the value of the NAME= key.
# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net",ACTION=="add",DRIVERS=="?*",ATTR{address}=="00:0c:29:13:d6:94",ATTR{type}=="1",KERNEL=="eth*",NAME="eth0"
?
# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net",ATTR{address}=="00:0c:29:13:d6:9e",NAME="eth1"
?
# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net",ATTR{address}=="00:50:56:22:c9:22",NAME="eth2"
?
# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net",ATTR{address}=="00:50:56:3a:fd:74",NAME="eth3"
删除原Mac,变动NAME值,搞定.改好后是这个样子.
[root@centos6 rules.d]# vim /etc/udev/rules.d/70-persistent-net.rules?
# This file was automatically generated by the /lib/udev/write_net_rules
# program,NAME="eth0"
# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net",NAME="eth1"
~
(2).重启或重装网卡驱动,使配置文件生效
查看网卡驱动名：ethtool -i eth2或dmesg|grep -i eth
卸载网卡驱动：modprobe -r e1000 或rmmod e1000
装载网卡驱动：modprobe e1000
[root@centos6 rules.d]# dmesg|grep -i eth
e1000 0000:02:01.0: eth0: (PCI:66MHz:32-bit) 00:50:56:3a:fd:74
e1000 0000:02:01.0: eth0: Intel(R) PRO/1000 Network Connection
e1000 0000:02:02.0: eth1: (PCI:66MHz:32-bit) 00:50:56:22:c9:22
e1000 0000:02:02.0: eth1: Intel(R) PRO/1000 Network Connection
udev: renamed network interface eth1 to eth2
udev: renamed network interface eth0 to eth3
e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex,Flow Control: None
8021q: adding VLAN 0 to HW filter on device eth3
e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex,Flow Control: None
8021q: adding VLAN 0 to HW filter on device eth2
eth2: no IPv6 routers present
eth3: no IPv6 routers present
#阿拉的网卡驱动只有e1000一块,所以阿拉卸载一块就够了.有的网卡名纷歧样,要分别卸载
[root@centos6 rules.d]# rmmod e1000
#再用ifconfig查看会发现原网卡信息不见了.(阿拉这一步就不粘代码了)
#装载网卡驱动
[root@centos6 rules.d]# modprobe e1000
#再次查看,修改成功
[root@centos6 ~]# ifconfig
eth0? ? ? Link encap:Ethernet? HWaddr 00:50:56:22:C9:22?
? ? ? ? ? inet addr:192.168.234.187? Bcast:192.168.234.255? Mask:255.255.255.0
? ? ? ? ? inet6 addr: fe80::250:56ff:fe22:c922/64 Scope:Link
? ? ? ? ? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1
? ? ? ? ? RX packets:3 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:1000?
? ? ? ? ? RX bytes:746 (746.0 b)? TX bytes:1152 (1.1 KiB)
?
eth1? ? ? Link encap:Ethernet? HWaddr 00:50:56:3A:FD:74?
? ? ? ? ? inet addr:172.17.251.174? Bcast:172.17.255.255? Mask:255.255.0.0
? ? ? ? ? inet6 addr: fe80::250:56ff:fe3a:fd74/64 Scope:Link
? ? ? ? ? UP BROADCAST RUNNING MULTICAST? MTU:1500? Metric:1
? ? ? ? ? RX packets:475 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:1000?
? ? ? ? ? RX bytes:48665 (47.5 KiB)? TX bytes:7289 (7.1 KiB)
?
lo? ? ? ? Link encap:Local Loopback?
? ? ? ? ? inet addr:127.0.0.1? Mask:255.0.0.0
? ? ? ? ? inet6 addr: ::1/128 Scope:Host
? ? ? ? ? UP LOOPBACK RUNNING? MTU:65536? Metric:1
? ? ? ? ? RX packets:80 errors:0 dropped:0 overruns:0 frame:0
? ? ? ? ? TX packets:80 errors:0 dropped:0 overruns:0 carrier:0
? ? ? ? ? collisions:0 txqueuelen:0?
? ? ? ? ? RX bytes:6148 (6.0 KiB)? TX bytes:6148 (6.0 KiB)
本文永远更新链接地址： 《LINUX入门：CentOS6 虚拟机迁移后网卡名更改问题解决》是否对您有启发，欢迎查看更多与《LINUX入门：CentOS6 虚拟机迁移后网卡名更改问题解决》相关教程，学精学透。编程之家PHP学院为您提供精彩教程。 （编辑：李大同）
【声明】本站内容均来自网络，其相关言论仅代表作者个人观点，不代表本站立场。若无意侵犯到您的权利，请及时与联系站长删除相关内容!
|
