交换机链路聚合
实验二十二、交换机链路聚合 一、 实验目的 1、了解链路聚合技术的使用场合; 2、熟练掌握链路聚合技术的配置。 二、 应用环境 两个实验室分别使用一台交换机提供20 多个信息点,两个实验室的互通通过一根级联 网线。每个实验室的信息点都是百兆到桌面。两个实验室之间的带宽也是100M,如果实验 室之间需要大量传输数据,就会明显感觉带宽资源紧张。当楼层之间大量用户都希望以100M 传输数据的时候,楼层间的链路就呈现出了独木桥的状态,必然造成网络传输效率下降等后 果。 解决这个问题的办法就是提高楼层主交换机之间的连接带宽,实现的办法可以是采用千 兆端口替换原来的 100M 端口进行互联,但这样无疑会增加组网的成本,需要更新端口模块, 并且线缆也需要作进一步的升级。另一种相对经济的升级办法就是链路聚合技术。 顾名思义,链路聚合,是将几个链路作聚合处理,这几个链路必须是同时连接两个相同 的设备的,这样,当作了链路聚合之后就可以实现几个链路相加的带宽了。比如,我们可以 将4 个 100M 链路使用链路聚合作成一个逻辑链路,这样在全双工条件下就可以达到 800M 的带宽,即将近1000M 的带宽。这种方式比较经济,实现也相对容易。 三、 实验设备 1、DCS-3926S 交换机 2 台 2、PC机 2 台 3、Console 线1-2 根 4、直通网线 4-8 根 四、 实验拓扑 五、 实验要求 设备 IP Mask 端口 交换机A 192.168.1.11 255.255.255.0 0/0/1-2 trunking 交换机B 192.168.1.12 255.255.255.0 0/0/3-4 trunking PC1 192.168.1.101 255.255.255.0 交换机A0/0/23 PC2 192.168.1.102 255.255.255.0 交换机B0/0/24 如果链路聚合成功,则PC1 可以ping 通PC2。 六、 实验步骤 第一步:正确连接网线,交换机全部恢复出厂设置,做初始配置,避免广播风暴出现 交换机A: switch#config switch(Config)#hostname switchA switchA(Config)#interface vlan 1 switchA(Config-If-Vlan1)#ip address 192.168.1.11 255.255.255.0 switchA(Config-If-Vlan1)#no shutdown switchA(Config-If-Vlan1)#exit switchA(Config)#spanning-tree MSTP is starting now,please wait........... MSTP is enabled successfully. switchA(Config)# 交换机B: switch#config switch(Config)#hostname switchB switchB(Config)#interface vlan 1 switchB(Config-If-Vlan1)#ip address 192.168.1.12 255.255.255.0 switchB(Config-If-Vlan1)#no shutdown switchB(Config-If-Vlan1)#exit switchB(Config)#spanning-tree MSTP is starting now,please wait........... MSTP is enabled successfully. switchB(Config)# 第二步:创建port group 交换机A: switchA(Config)#port-group 1 switchA(Config)# 验证配置: switchA#show port-group detail Sorted by the ports in the group 1: -------------------------------------------- switchA#show port-group brief Port-group number : 1 Number of ports in port-group : 0 Maxports in port-channel = 8 Number of port-channels : 0 Max port-channels : 1 switchA# 交换机B switchB(Config)#port-group 2 switchB(Config)# 第三步:手工生成链路聚合组(第三、四步任选其一操作) 交换机A: switchA(Config)#interface ethernet 0/0/1-2 switchA(Config-Port-Range)#port-group 1 mode on switchA(Config-Port-Range)#exit switchA(Config)#interface port-channel 1 switchA(Config-If-Port-Channel1)# 验证配置: switchA#show vlan VLAN Name Type Media Ports ---- ------------ ---------- --------- ------------------- 1 default Static ENET Ethernet0/0/3 Ethernet0/0/4 Ethernet0/0/5 Ethernet0/0/6 Ethernet0/0/7 Ethernet0/0/8 Ethernet0/0/9 Ethernet0/0/10 Ethernet0/0/11 Ethernet0/0/12 Ethernet0/0/13 Ethernet0/0/14 Ethernet0/0/15 Ethernet0/0/16 Ethernet0/0/17 Ethernet0/0/18 Ethernet0/0/19 Ethernet0/0/20 Ethernet0/0/21 Ethernet0/0/22 Ethernet0/0/23 Ethernet0/0/24 Port-Channel1 switchA# !port-channel1已经存在 交换机B: switchB(Config)#int e 0/0/3-4 switchB(Config-Port-Range)#port-group 2 mode on switchB(Config-Port-Range)#exit switchB(Config)#interface port-channel 2 switchB(Config-If-Port-Channel2)# 验证配置: switchB#show port-group brief Port-group number : 2 Number of ports in port-group : 2 Maxports in port-channel = 8 Number of port-channels : 1 Max port-channels : 1 switchB# 第四步: LACP动态生成链路聚合组 (第三、四步任选其一操作) switchA(Config)#interface ethernet 0/0/1-2 switchA(Conifg-Port-Range)#port-group 1 mode active switchA(Config)#interface port-channel 1 switchA(Config-If-Port-Channel1)# 验证配置: switchA#show vlan VLAN Name Type Media Ports ---- ------------ ---------- --------- ------------------- 1 default Static ENET Ethernet0/0/3 Ethernet0/0/4 Ethernet0/0/5 Ethernet0/0/6 Ethernet0/0/7 Ethernet0/0/8 Ethernet0/0/9 Ethernet0/0/10 Ethernet0/0/11 Ethernet0/0/12 Ethernet0/0/13 Ethernet0/0/14 Ethernet0/0/15 Ethernet0/0/16 Ethernet0/0/17 Ethernet0/0/18 Ethernet0/0/19 Ethernet0/0/20 Ethernet0/0/21 Ethernet0/0/22 Ethernet0/0/23 Ethernet0/0/24 Port-Channel1 switchA# !port-channel1已经存在 交换机B: switchB(Config)#interface ethernet 0/0/3-4 switchB(Conifg-Port-Range)#port-group 2 mode passive switchB(Config)#interface port-channel 2 switchB(Config-If-Port-Channel2)# 验证配置: switchB#show port-group brief Port-group number : 2 Number of ports in port-group : 2 Maxports in port-channel = 8 Number of port-channels : 1 Max port-channels : 1 switchB# 第九步:使用ping命令验证 使用PC1 ping PC2 交换机A 交换机B 结果 原因 0/0/1 0/0/3 通 链路聚合组连接正确 0/0/2 0/0/4 0/0/1 0/0/3 通 拔掉交换机B端口4的网线,仍然可 0/0/2 以通(需要一点时间),此时用show vlan 看看结果,port-channel消 失。只有一个端口连接的时候,没 有必要再维持一个port-channel 了。 0/0/1 0/0/5 通 等候一小段时间后,仍然是通的。 0/0/2 0/0/6 用show vlan看结果。此时把两台交 换机的spanning-tree功能disable 掉,这时候使用第三步和第四步的 结果会不同。采用第四步的,将会 形成环路。 (编辑:李大同) 【声明】本站内容均来自网络,其相关言论仅代表作者个人观点,不代表本站立场。若无意侵犯到您的权利,请及时与联系站长删除相关内容! |