折腾了几天,刀片终于上架了,开始了网络配置,通过管理口登录管理刀箱,但开始配置,之前从来没有碰过刀片,居然以为插上电简单配置一下就可以通了,谁知道一个刀箱上居然有两个交换机需要配置,到ibm官方网站上去查,居然有3个牌子的手册,据说是找cisco、北电、博科三家厂商oem的,我都不知道看那个,全部下载下来研究吧。
最后发现这个应该是北电的,好像是博科把北电收购了,上面的标貌似博科。哈哈,看的差不多了就开始配置了(当然有高手在,我自己的话估计够呛)。
由于项目需求,需要把带万兆光口的交换机(ibm 刀箱背板上的交换机)和博科 rx-16做爽端口绑定,就是我们常说的链路聚合(目的当然是冗余和加大带宽)。当然在配置中遇到了不少问题,2天之中从博科交换机到ibm交换机,再到ibm刀箱背板交换机。都是以前没用过的。
bnt用于计算网络
nt用于管理网
我们需要把背板上的bnt交换机的两个万兆口做聚合与博客交换机的连接,当然博客交换机上也是配置聚合,nt交换机就比较简单了,把tag标签去掉。纯2层模式就可以了。
一、配置前检查
bnt进入交换机
进交换机之前先检查交换机是否是干净的状态。 info进 入主菜单输入info,这里面是查看信息的地方 首先检查port 然后检查lacp 动态聚合 可以检查vlan 如果有可以删除,之后才继续安装。
二、配置
1、取消tag标签 cfg进入配置模式 port 1-14 (不能批量,只能一个一个的敲) tag d把tag改为untag模式(与cisco的trunk到access类似,但是cisco默认为access口)
apply info port
2、配置trunk cfg trunk ena 选择 1 add ext1 add ext2 将口放入trunk apply diff
nt交换机配置用步骤1就修改为纯2层模式了
下面为具体是配置:
>> Main# info ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# port Alias Port Tag Fast Lrn Fld PVID NAME VLAN(s) ----- ---- --- ---- --- ---- -------------- ------------------------------- INT1 1 y n e e 1 INT1 1 4095 INT2 2 y n e e 1 INT2 1 4095 INT3 3 y n e e 1 INT3 1 4095 INT4 4 y n e e 1 INT4 1 4095 INT5 5 y n e e 1 INT5 1 4095 INT6 6 y n e e 1 INT6 1 4095 INT7 7 y n e e 1 INT7 1 4095 INT8 8 y n e e 1 INT8 1 4095 INT9 9 y n e e 1 INT9 1 4095 INT10 10 y n e e 1 INT10 1 4095 INT11 11 y n e e 1 INT11 1 4095 INT12 12 y n e e 1 INT12 1 4095 INT13 13 y n e e 1 INT13 1 4095 INT14 14 y n e e 1 INT14 1 4095 MGT1 15 y n e e 4095*MGT1 4095 MGT2 16 y n e e 4095*MGT2 4095 EXT1 17 n n e e 1 EXT1 1 EXT2 18 n n e e 1 EXT2 1 EXT3 19 n n e e 1 EXT3 1 EXT4 20 n n e e 1 EXT4 1 EXT5 21 n n e e 1 EXT5 1 EXT6 22 n n e e 1 EXT6 1 EXT7 23 n n e e 1 EXT7 1 EXT8 24 n n e e 1 EXT8 1 EXT9 25 n n e e 1 EXT9 1 * = PVID is tagged.
>> Information# ls ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# lacp ------------------------------------------------------------ [LACP Menu] aggr - Show LACP aggregator information for the port port - Show LACP port information dump - Show all LACP ports information
>> LACP# dump port lacp adminkey operkey selected prio attached trunk aggr ---------------------------------------------------------------------------- INT1 off 1 1 no 32768 -- -- INT2 off 2 2 no 32768 -- -- INT3 off 3 3 no 32768 -- -- INT4 off 4 4 no 32768 -- -- INT5 off 5 5 no 32768 -- -- INT6 off 6 6 no 32768 -- -- INT7 off 7 7 no 32768 -- -- INT8 off 8 8 no 32768 -- -- INT9 off 9 9 no 32768 -- -- INT10 off 10 10 no 32768 -- -- INT11 off 11 11 no 32768 -- -- INT12 off 12 12 no 32768 -- -- INT13 off 13 13 no 32768 -- -- INT14 off 14 14 no 32768 -- -- EXT1 off 17 17 no 32768 -- -- EXT2 off 18 18 no 32768 -- -- EXT3 off 19 19 no 32768 -- -- EXT4 off 20 20 no 32768 -- -- EXT5 off 21 21 no 32768 -- -- EXT6 off 22 22 no 32768 -- -- EXT7 off 23 23 no 32768 -- -- EXT8 off 24 24 no 32768 -- -- EXT9 off 25 25 no 32768 -- --
>> LACP# cd .. ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# ls ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# cd .. ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# vlan VLAN Name Status Ports ---- -------------------------------- ------ ------------------------- 1 Default VLAN ena INT1-INT14 EXT1-EXT9 4095 Mgmt VLAN ena INT1-INT14 MGT1 MGT2
>> Layer 2# lacp ------------------------------------------------------------ [LACP Menu] aggr - Show LACP aggregator information for the port port - Show LACP port information dump - Show all LACP ports information
>> LACP# port Usage: port <port INT1-14,EXT1-9>
>> LACP# cd .. ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# cd / ------------------------------------------------------------ [Main Menu] info - Information Menu stats - Statistics Menu cfg - Configuration Menu oper - Operations Command Menu boot - Boot Options Menu maint - Maintenance Menu diff - Show pending config changes [global command] apply - Apply pending config changes [global command] save - Save updated config to FLASH [global command] revert - Revert pending or applied changes [global command] exit - Exit [global command,always available]
>> Main# cfg ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port Enter port (INT1-14,MGT1-2,EXT1-9): 1 ------------------------------------------------------------ [Port INT1 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT1# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT1 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT1# apply ------------------------------------------------------------------ Apply complete; don't forget to "save" updated configuration.
>> Jan 2 8:47:54 170.120.116.224 INFO mgmt: new configuration applied Port INT1# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 2 ------------------------------------------------------------ [Port INT2 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT2# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT2 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT2# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 3 ------------------------------------------------------------ [Port INT3 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT3# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT3 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT3# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 4 ------------------------------------------------------------ [Port INT4 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT4# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT4 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT4# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 5 ------------------------------------------------------------ [Port INT5 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT5# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT5 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT5# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 6 ------------------------------------------------------------ [Port INT6 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT6# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT6 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT6# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 7 ------------------------------------------------------------ [Port INT7 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT7# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT7 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT7# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 8 ------------------------------------------------------------ [Port INT8 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT8# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT8 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT8# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 9 ------------------------------------------------------------ [Port INT9 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT9# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT9 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT9# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 10 ------------------------------------------------------------ [Port INT10 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT10# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT10 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT10# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 11 ------------------------------------------------------------ [Port INT11 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT11# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT11 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT11# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 12 ------------------------------------------------------------ [Port INT12 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT12# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT12 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT12# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 13 ------------------------------------------------------------ [Port INT13 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT13# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT13 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT13# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# port 14 ------------------------------------------------------------ [Port INT14 Menu] gig - Gig Phy Menu aclqos - Acl/Qos Configuration Menu 8021ppri - Set default 802.1p priority pvid - Set default port VLAN id name - Set port name dscpmrk - Enable/disable DSCP remarking for port learn - Enable/Disable FDB Learning for port tag - Enable/disable VLAN tagging for port tagpvid - Enable/disable tagging on pvid fastfwd - Enable/disable Port Fast Forwarding mode floodblk - Enable/disable Port flood blocking ena - Enable port dis - Disable port cur - Display current port configuration
>> Port INT14# tag d Current VLAN tag support: enabled New VLAN tag support: disabled Port INT14 will be removed from all VLANs except its PVID. Confirm removing this port from all VLANs [y/n]: y TAG flag reset
>> Port INT14# apply ------------------------------------------------------------------ Apply complete; don't forget to "save" updated configuration.
>> Jan 2 8:50:23 170.120.116.224 INFO mgmt: new configuration applied Port INT14# save Request will first copy the FLASH "active" config to "backup", then overlay FLASH "active" with new config. Confirm saving to FLASH [y/n]: y New config successfully saved to FLASH. Switch is currently set to use factory default config block on next boot.
Jan 2 8:50:39 170.120.116.224 INFO mgmt: new configuration saved from AOS Confirm change that to the active config block [y/n]: y Next boot will use active config block.
>> Jan 2 8:50:47 170.120.116.224 NOTICE mgmt: boot config block changed Port INT14# cd .. ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# cd .. ------------------------------------------------------------ [Main Menu] info - Information Menu stats - Statistics Menu cfg - Configuration Menu oper - Operations Command Menu boot - Boot Options Menu maint - Maintenance Menu diff - Show pending config changes [global command] apply - Apply pending config changes [global command] save - Save updated config to FLASH [global command] revert - Revert pending or applied changes [global command] exit - Exit [global command,always available]
>> Main# info ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# port Alias Port Tag Fast Lrn Fld PVID NAME VLAN(s) ----- ---- --- ---- --- ---- -------------- ------------------------------- INT1 1 n n e e 1 INT1 1 INT2 2 n n e e 1 INT2 1 INT3 3 n n e e 1 INT3 1 INT4 4 n n e e 1 INT4 1 INT5 5 n n e e 1 INT5 1 INT6 6 n n e e 1 INT6 1 INT7 7 n n e e 1 INT7 1 INT8 8 n n e e 1 INT8 1 INT9 9 n n e e 1 INT9 1 INT10 10 n n e e 1 INT10 1 INT11 11 n n e e 1 INT11 1 INT12 12 n n e e 1 INT12 1 INT13 13 n n e e 1 INT13 1 INT14 14 n n e e 1 INT14 1 MGT1 15 y n e e 4095*MGT1 4095 MGT2 16 y n e e 4095*MGT2 4095 EXT1 17 n n e e 1 EXT1 1 EXT2 18 n n e e 1 EXT2 1 EXT3 19 n n e e 1 EXT3 1 EXT4 20 n n e e 1 EXT4 1 EXT5 21 n n e e 1 EXT5 1 EXT6 22 n n e e 1 EXT6 1 EXT7 23 n n e e 1 EXT7 1 EXT8 24 n n e e 1 EXT8 1 EXT9 25 n n e e 1 EXT9 1 * = PVID is tagged.
>> Information# cd / ------------------------------------------------------------ [Main Menu] info - Information Menu stats - Statistics Menu cfg - Configuration Menu oper - Operations Command Menu boot - Boot Options Menu maint - Maintenance Menu diff - Show pending config changes [global command] apply - Apply pending config changes [global command] save - Save updated config to FLASH [global command] revert - Revert pending or applied changes [global command] exit - Exit [global command,always available]
>> Main# Jan 2 8:56:08 170.120.116.224 ALERT stg: Port EXT2,putting port into blocking state
>> Main# cfg ------------------------------------------------------------ [Configuration Menu] sys - System-wide Parameter Menu port - Port Menu pmirr - Port Mirroring Menu l2 - Layer 2 Menu l3 - Layer 3 Menu qos - QOS Menu acl - Access Control List Menu setup - Step by step configuration set up dump - Dump current configuration to script file ptcfg - Backup current configuration to FTP/TFTP server gtcfg - Restore current configuration from FTP/TFTP server cur - Display current configuration
>> Configuration# l2 ------------------------------------------------------------ [Layer 2 Menu] 8021x - 802.1x Menu mrst - Multiple Spanning Tree/Rapid Spanning Tree Menu stg - Spanning Tree Menu fdb - FDB Menu trunk - Trunk Group Menu thash - IP Trunk Hash Menu lacp - Link Aggregation Control Protocol Menu failovr - Failover Menu vlan - VLAN Menu pvstcomp - Enable/Disable PVST+ compatibility mode bpdugrd - Enable/disable BPDU Guard macnotif - Enable/disable MAC address notification upfast - Enable/disable Uplink Fast update - UplinkFast station update rate cur - Display current layer 2 parameters
>> Layer 2# trunk/ Enter trunk group number: (1-16) 1 ------------------------------------------------------------ [Trunk group 1 Menu] add - Add port to trunk group rem - Remove port from trunk group ena - Enable trunk group dis - Disable trunk group del - Delete trunk group cur - Display current Trunk Group configuration
>> Trunk group 1# add Enter port (INT1-EXT9): ext1 Port EXT1 added. Reminder: Trunk 1 needs to be enabled.
>> Trunk group 1# add ext2 Port EXT2 added. Reminder: Trunk 1 needs to be enabled.
>> Trunk group 1# apply ------------------------------------------------------------------ Apply complete; don't forget to "save" updated configuration.
>> Jan 2 8:57:46 170.120.116.224 INFO mgmt: new configuration applied Trunk group 1# cd / ------------------------------------------------------------ [Main Menu] info - Information Menu stats - Statistics Menu cfg - Configuration Menu oper - Operations Command Menu boot - Boot Options Menu maint - Maintenance Menu diff - Show pending config changes [global command] apply - Apply pending config changes [global command] save - Save updated config to FLASH [global command] revert - Revert pending or applied changes [global command] exit - Exit [global command,always available]
>> Main# info ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# dump ------------------------------------------------------------------
upfast disabled,update 40
BPDU Guard disabled
Pvst+ compatibility mode enabled
------------------------------------------------------------------ Spanning Tree Group 1: On (STP/PVST+) VLANs: 1
Current Root: Path-Cost Port Hello MaxAge FwdDel ffff 34:40:b5:60:c5:00 2 EXT1 2 20 15
Parameters: Priority Hello MaxAge FwdDel Aging 65535 2 20 15 300
Port Priority Cost FastFwd State Designated Bridge Des Port ---- -------- ---- -------- ---------- --------------------- -------- INT1 0 0 n FORWARDING * INT2 0 0 n FORWARDING * INT3 0 0 n FORWARDING * INT4 0 0 n FORWARDING * INT5 0 0 n FORWARDING * INT6 0 0 n FORWARDING * INT7 0 0 n FORWARDING * INT8 0 0 n FORWARDING * INT9 0 0 n FORWARDING * INT10 0 0 n FORWARDING * INT11 0 0 n FORWARDING * INT12 0 0 n FORWARDING * INT13 0 0 n FORWARDING * INT14 0 0 n FORWARDING * EXT1 128 2 n FORWARDING ffff-34:40:b5:60:c5:00 8012 EXT2 128 2 n BLOCKING ffff-34:40:b5:6f:f4:00 8011 EXT3 128 2 n DISABLED EXT4 128 0! n DISABLED EXT5 128 0! n DISABLED EXT6 128 0! n DISABLED EXT7 128 0! n DISABLED EXT8 128 0! n DISABLED EXT9 128 0! n DISABLED * = STP turned off for this port. ! = Automatic path cost.
------------------------------------------------------------------ Spanning Tree Group 128: On (STP/PVST+) VLANs: 4095
Current Root: Path-Cost Port Hello MaxAge FwdDel ffff 34:40:b5:70:62:00 0 2 20 15
Parameters: Priority Hello MaxAge FwdDel Aging 65535 2 20 15 300
Port Priority Cost FastFwd State Designated Bridge Des Port ---- -------- ---- -------- ---------- --------------------- -------- MGT1 0 0 n FORWARDING * MGT2 0 0 n DISABLED * * = STP turned off for this port.
VLAN Name Status Ports ---- -------------------------------- ------ ------------------------- 1 Default VLAN ena INT1-INT14 EXT1-EXT9 4095 Mgmt VLAN ena MGT1 MGT2
Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
Current priority to COS queue information: Priority COSq Weight -------- ---- ------ 0 0 1 1 0 1 2 0 1 3 0 1 4 1 2 5 1 2 6 1 2 7 1 2
Current port priority information: Port Priority COSq Weight ----- -------- ---- ------ INT1 0 0 1 INT2 0 0 1 INT3 0 0 1 INT4 0 0 1 INT5 0 0 1 INT6 0 0 1 INT7 0 0 1 INT8 0 0 1 INT9 0 0 1 INT10 0 0 1 INT11 0 0 1 INT12 0 0 1 INT13 0 0 1 INT14 0 0 1 MGT1 0 0 1 MGT2 0 0 1 EXT1 0 0 1 EXT2 0 0 1 EXT3 0 0 1 EXT4 0 0 1 EXT5 0 0 1 EXT6 0 0 1 EXT7 0 0 1 EXT8 0 0 1 EXT9 0 0 1
Forwarding database information: MAC address VLAN Port Trnk State Permanent ----------------- ---- ---- ---- ----- --------- 00:25:90:61:17:0f 1 EXT1 FWD 00:25:90:61:c8:75 1 EXT1 FWD 00:25:90:61:ca:85 1 EXT1 FWD 34:40:b5:60:c5:00 1 EXT1 FWD 34:40:b5:64:85:00 1 EXT1 FWD 5c:f3:fc:ef:5b:c7 4095 MGT1 FWD
802.1x Operational Info: ------------------------------------------------------------------ System capability : Authenticator System status : disabled Protocol version : 1 Guest VLAN status : disabled Guest VLAN : none Authenticator Backend Port Auth Mode Auth Status PAE State Auth State ----- ------------ ------------ -------------- ---------- INT1 force-auth unauthorized initialize initialize INT2 force-auth unauthorized initialize initialize INT3 force-auth unauthorized initialize initialize INT4 force-auth unauthorized initialize initialize INT5 force-auth unauthorized initialize initialize INT6 force-auth unauthorized initialize initialize INT7 force-auth unauthorized initialize initialize INT8 force-auth unauthorized initialize initialize INT9 force-auth unauthorized initialize initialize INT10 force-auth unauthorized initialize initialize INT11 force-auth unauthorized initialize initialize INT12 force-auth unauthorized initialize initialize INT13 force-auth unauthorized initialize initialize INT14 force-auth unauthorized initialize initialize EXT1 force-auth unauthorized initialize initialize EXT2 force-auth unauthorized initialize initialize *EXT3 force-auth unauthorized initialize initialize *EXT4 force-auth unauthorized initialize initialize *EXT5 force-auth unauthorized initialize initialize *EXT6 force-auth unauthorized initialize initialize *EXT7 force-auth unauthorized initialize initialize *EXT8 force-auth unauthorized initialize initialize *EXT9 force-auth unauthorized initialize initialize ------------------------------------------------------------------ * - Port down or disabled
STP uplink fast mode : disabled
>> Layer 2# cd .. ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# cd .. ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# cd .. ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information#
>> Information#
>> Information#
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# cd / ------------------------------------------------------------ [Main Menu] info - Information Menu stats - Statistics Menu cfg - Configuration Menu oper - Operations Command Menu boot - Boot Options Menu maint - Maintenance Menu diff - Show pending config changes [global command] apply - Apply pending config changes [global command] save - Save updated config to FLASH [global command] revert - Revert pending or applied changes [global command] exit - Exit [global command,always available]
>> Main# info ------------------------------------------------------------ [Information Menu] sys - System Information Menu l2 - Layer 2 Information Menu l3 - Layer 3 Information Menu qos - QoS Menu acl - Show ACL information link - Show link status port - Show port information transcvr - Show Port Transceiver status dump - Dump all information
>> Information# l2 ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# lacp ------------------------------------------------------------ [LACP Menu] aggr - Show LACP aggregator information for the port port - Show LACP port information dump - Show all LACP ports information
>> LACP# dump port lacp adminkey operkey selected prio attached trunk aggr ---------------------------------------------------------------------------- INT1 off 1 1 no 32768 -- -- INT2 off 2 2 no 32768 -- -- INT3 off 3 3 no 32768 -- -- INT4 off 4 4 no 32768 -- -- INT5 off 5 5 no 32768 -- -- INT6 off 6 6 no 32768 -- -- INT7 off 7 7 no 32768 -- -- INT8 off 8 8 no 32768 -- -- INT9 off 9 9 no 32768 -- -- INT10 off 10 10 no 32768 -- -- INT11 off 11 11 no 32768 -- -- INT12 off 12 12 no 32768 -- -- INT13 off 13 13 no 32768 -- -- INT14 off 14 14 no 32768 -- -- EXT1 off 17 17 no 32768 -- -- EXT2 off 18 18 no 32768 -- -- EXT3 off 19 19 no 32768 -- -- EXT4 off 20 20 no 32768 -- -- EXT5 off 21 21 no 32768 -- -- EXT6 off 22 22 no 32768 -- -- EXT7 off 23 23 no 32768 -- -- EXT8 off 24 24 no 32768 -- -- EXT9 off 25 25 no 32768 -- --
>> LACP# cd .. ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# apply No apply needed.
>> Layer 2# Jan 2 9:11:36 170.120.116.224 ALERT stg: Port EXT1,putting port into blocking state
Jan 2 9:11:36 170.120.116.224 ALERT stg: Port EXT2,putting port into blocking state
Jan 2 9:11:36 170.120.116.224 ALERT stg: Port EXT1,putting port into blocking state
Jan 2 9:12:03 170.120.116.224 ALERT stg: STG 1,topology change detected
Jan 2 9:12:03 170.120.116.224 ALERT stg: Port EXT2,putting port into blocking state
>> Layer 2#
>> Layer 2#
>> Layer 2#
>> Layer 2#
>> Layer 2#
>> Layer 2# ls ------------------------------------------------------------ [Layer 2 Menu] fdb - Forwarding Database Information Menu lacp - Link Aggregation Control Protocol Menu 8021x - Show 802.1x information stg - Show STP information cist - Show CIST information trunk - Show Trunk Group information vlan - Show VLAN information dump - Dump all layer 2 information
>> Layer 2# trunk Trunk group 1: Disabled Reminder: Trunk group 1 needs to be enabled. Protocol - Static port state: EXT1: STG 1 forwarding EXT2: STG 1 BLOCKING
>> Layer 2# Jan 2 9:13:19 170.120.116.224 ALERT stg: STG 1,topology change detected
我上面出现ext2 blocking 是因为我配置了trunk 没有enable,所以出现这个情况
database群:119224876(db china联盟) 虚拟化方面群:229845401(虚拟化-云计算-物联网) (编辑:李大同)
【声明】本站内容均来自网络,其相关言论仅代表作者个人观点,不代表本站立场。若无意侵犯到您的权利,请及时与联系站长删除相关内容!
|