cisco 以太通道(端口聚合)配置样例
3.4.1EtherChannel及其作用 交换机允许将多个端口聚合成一个逻辑端口或者称为EtherChannel。 通过端口聚合,可大大提高端口间链路的通信速度。比如,当用2个100Mbit/s的端口进行聚合时,所形成的逻辑端口的通信速度为200Mbit/s;若用4个,则为400Mbit/s。当EtherChannel内的某条链路出现故障时,该链路的流量将自动转移到其余链路上,自动提供冗余和负载均衡。 PAgP是Cisco专有的端口聚合协议,LACP(Link Aggregation Control Protocol,链路聚合控制协议)则是一种标准的协议。 3.4.2 EtherChannel配置 参与聚合的端口必须具备相同的属性,如相同的速度、单双工模式、trunk模式、trunk封装方式和VLAN等。端口配置模式下使用命令: channel-group number mode [active|auto|desirable |on|passive] 进行配置。 参数说明: active只使用LACP协议(Enable LACP unconditionally) auto使用PAgP仅当对端设备使用PagP时( Enable PAgP only if a PAgP device is detected) desirable只使用PAgP(Enable PAgP unconditionally) on只进行端口聚合,默认使用PAgP(Enable Etherchannel only) passive使用LACP仅当对端设备使用LACP时(Enable LACP only if a LACP device is detected) 两端设备对应端口聚合应该使用同样的协议,否则至少有一端的聚合不会成功。 1.配置实例 比如在如图所示的网络中,两核心交换机之间的链路采用两个端口的EtherChannel。
配置步骤: Sw0(config)#interface range G0/1-2//配置G0/1和G0/2口 Sw0(config-if)#channel-group 10 mode on//可理解为把G0/1-2加入10号逻辑端口组(通道组) Sw0(config-if)#exit Sw1(config)#interface range G0/1-2 Sw1(config-if)#channel-group 10 mode on Sw1(config-if)#exit 2.查看配置: SW1#show etherchannel summary Flags:D - downP - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3S - Layer2 U - in usef - failed to allocate aggregator u - unsuitable for bundling w - waiting to be aggregated d - default port Number of channel-groups in use: 1 Number of aggregators:1 GroupPort-channelProtocolPorts ------+-------------+-----------+---------------------------------------------- 10Po10(SU)PAgP Gig0/1(P)Gig0/2(P) 显示这两个接口已经捆绑成为一个通道组接口Port-channel 10,Po10(SU)中的“S”说明这个通道组接口工作在第二层,U表示已在使用,使用的协议为PAgP,通道组聚合了两个接口Gig0/1和Gig0/2。 Cisco 3560交换机支持48个EtherChannel配置,每组最多支持8个端口聚合。 3.负载均衡配置 EtherChannel可以自动执行负载均衡,当EtherChannel执行负载均衡时,按照默认策略进行。 可以根据不同条件来决定和配置负载均衡策略。如MAC地址、IP地址等都可以作为负载均衡策略的参数。但是不是每种交换机都能支持所有这些参数,越高端的交换机支持的参数就越多。 例如,Cisco 3560的负载均衡配置 Switch(config)#port-channel load-balance ? dst-ipDst IP Addr dst-mac Dst Mac Addr src-dst-ipSrc XOR Dst IP Addr src-dst-macSrc XOR Dst Mac Addr src-ipSrc IP Addr src-macSrc Mac Addr 支持多种策略 =============================== **************** 链路聚合 **************** int ran f0/1 - 2 SW2:2960 int ran f0/1 - 2 SW3:2960 int ran f0/1 - 2 SW4:2960 int ran f0/1 - 2
int ran f0/1 - 2 interface Port-channel 2 int ran f0/3 - 4 interface Port-channel 3 int ran f0/5 - 6 interface Port-channel 4 int ran f0/7 - 8 sh ip int bri (编辑:李大同) 【声明】本站内容均来自网络,其相关言论仅代表作者个人观点,不代表本站立场。若无意侵犯到您的权利,请及时与联系站长删除相关内容! |